| Author |
 Topic  |
|
|
NSAELLIS
Senior Modder
OK
1100 Posts |
 Posted - 10/08/2010 : 13:33:51
|
| I need a Motor for a Dumar Pontiac & Power Wheels Hurricane |
Visit WWW.NSAWOODWORKING.COM for New and Used National Products, Little Tikes,Peg- Perego, Power Wheels, Kid Trax, & Razor. We also have Swing-N-Slide, Kidwise, & Jensen swing Accessories & Kits.
Black Corvette SOLD
Red Corvette
Cinderella Solstice
Purple Princess Solstice
Beach Patrol
Barbie Beach Buggy
Re MF Jeep
Barbie Escalade
6V Ford 150 Bigfoot
Red Hummer (In Work) |
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/10/2010 : 12:50:16
|
quote:
Originally posted by NSAELLIS
I need a Motor for a Dumar Pontiac & Power Wheels Hurricane
I have (2) 19 tooth motors, and one 16 tooth motor, not sure if that is what you are looking for.
Any chance you have a PC board for the PW Kawasaki Quad? I wanted to get an extra one to have on hand.
Thank you! |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
Edited by - timmbo23 on 10/11/2010 08:05:21 |
 |
|
|
|
|
NSAELLIS
Senior Modder
OK
1100 Posts |
Posted - 10/11/2010 : 15:06:47
|
| Unsure what the Hurricane I just know the diameter of the gear on the motor is smaller than the 19t Motot Gear |
Visit WWW.NSAWOODWORKING.COM for New and Used National Products, Little Tikes,Peg- Perego, Power Wheels, Kid Trax, & Razor. We also have Swing-N-Slide, Kidwise, & Jensen swing Accessories & Kits.
Black Corvette SOLD
Red Corvette
Cinderella Solstice
Purple Princess Solstice
Beach Patrol
Barbie Beach Buggy
Re MF Jeep
Barbie Escalade
6V Ford 150 Bigfoot
Red Hummer (In Work) |
|
|
|
Divinar
Moderator
San Jose 95123
CA
USA
3057 Posts |
Posted - 10/11/2010 : 16:01:41
|
I'm pretty sure the Hurricaine stock was 13T - but the new ones have a new 13T gearbox and motor combo that aren't the same as the old ones.
I don't know what is different though. |
Escalade (Rubber tires, LED lights, Key switch, Remote Kill, wings. Wings?)
Lil Wrangler (2WD, 12v, Lights), Dora Jeep (Super-6 @ 12v, lights), Jeep Enforcer turned Aftershock (18v, WIP),
Grape Gaucho A151 (24v, scooter controller, WIP)
KFX Quad (Remote Kill), Crushmeister! (Silverado), Limited Edition Jeep (Stock)
Kawasaki Mojave 250 (Stock), PP Gator (Lights), Home Depot Loader, Lightning McQueen (Stock) |
|
|
|
NSAELLIS
Senior Modder
OK
1100 Posts |
Posted - 10/16/2010 : 08:53:12
|
| That sucks I guess I'm going to have to brake down and take it to the Power wheels service center in town and have then replace the motor unless some one can tell me how to remove the gear off the motor. IF i can do that I can take one of the many motors I have and swap it. Any one? |
Visit WWW.NSAWOODWORKING.COM for New and Used National Products, Little Tikes,Peg- Perego, Power Wheels, Kid Trax, & Razor. We also have Swing-N-Slide, Kidwise, & Jensen swing Accessories & Kits.
Black Corvette SOLD
Red Corvette
Cinderella Solstice
Purple Princess Solstice
Beach Patrol
Barbie Beach Buggy
Re MF Jeep
Barbie Escalade
6V Ford 150 Bigfoot
Red Hummer (In Work) |
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/16/2010 : 09:27:58
|
quote:
Originally posted by NSAELLIS
That sucks I guess I'm going to have to brake down and take it to the Power wheels service center in town and have then replace the motor unless some one can tell me how to remove the gear off the motor. IF i can do that I can take one of the many motors I have and swap it. Any one?
I think it is almost impossible to get the gear (pinion) off of the stock motor on the newer Power Wheels. Your best bet is to find a motor with the proper number of teeth on it. Personally I would tell you this is a great time to buy 2 HPI GT550 motors and upgrade your Hurricane so it is much faster. You can find those motors for about $14 each (sometimes even a few bucks less!). You will also need to purchase 2 pinions which are usually $3 or $4 each, quick and easy to do and does not require a PW service center!!!!! |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
|
|
chozian
Expert Modder
Meridianville
AL (35759)
USA
631 Posts |
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/25/2010 : 12:36:12
|
quote:
Originally posted by chozian
quote:
Originally posted by timmbo23
I think it is almost impossible to get the gear (pinion) off of the stock motor on the newer Power Wheels. Your best bet is to find a motor with the proper number of teeth on it. Personally I would tell you this is a great time to buy 2 HPI GT550 motors and upgrade your Hurricane so it is much faster. You can find those motors for about $14 each (sometimes even a few bucks less!). You will also need to purchase 2 pinions which are usually $3 or $4 each, quick and easy to do and does not require a PW service center!!!!!
What is it about the stock motor on newer Power Wheels that makes it so difficult?
I don't know what they do to secure it to the shaft, but there is nothing I could do to get that pinion to budge off of there. The shaft of the motor actually started to slightly pull out of the back of the motor, I ended up bending the shaft and junked the old motor. |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
ms1120
Senior Modder
M-Town
Georgia
USA
1464 Posts |
Posted - 10/25/2010 : 12:53:30
|
| They press the pinion on and the oversize the remaining shaft so that it doesnt slide off. Grind the end of the shaft off flush with the pinion and then use a press or punch and vice to take it off. |
Fixing things that arent broken...and making them cool
 |
|
|
|
ms1120
Senior Modder
M-Town
Georgia
USA
1464 Posts |
|
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/25/2010 : 13:06:36
|
| The only reason I wanted to remove the pinion from the stock motor was so I could get the plastic washers off of the motor to use on the new motor. I ended up cutting a small slit in the plastic washer so I could get it past the stock pinion. |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
ms1120
Senior Modder
M-Town
Georgia
USA
1464 Posts |
Posted - 10/25/2010 : 13:10:41
|
quote:
Originally posted by timmbo23
quote:
Originally posted by chozian
quote:
Originally posted by timmbo23
I think it is almost impossible to get the gear (pinion) off of the stock motor on the newer Power Wheels. Your best bet is to find a motor with the proper number of teeth on it. Personally I would tell you this is a great time to buy 2 HPI GT550 motors and upgrade your Hurricane so it is much faster. You can find those motors for about $14 each (sometimes even a few bucks less!). You will also need to purchase 2 pinions which are usually $3 or $4 each, quick and easy to do and does not require a PW service center!!!!!
What is it about the stock motor on newer Power Wheels that makes it so difficult?
I don't know what they do to secure it to the shaft, but there is nothing I could do to get that pinion to budge off of there. The shaft of the motor actually started to slightly pull out of the back of the motor, I ended up bending the shaft and junked the old motor.
You, my friend, didnt use a B.F.H. |
Fixing things that arent broken...and making them cool
|
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/25/2010 : 13:29:02
|
| What is that? |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
ms1120
Senior Modder
M-Town
Georgia
USA
1464 Posts |
Posted - 10/25/2010 : 19:30:36
|
| Bigger F$%#@*g Hammer |
Fixing things that arent broken...and making them cool
|
|
|
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/26/2010 : 13:03:58
|
| Dude, that thing did not budge!!!!! |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
treebeme
Advanced Modder
Holtsville
NY
USA
3209 Posts |
Posted - 10/26/2010 : 15:53:49
|
NSAELLIS, I just gave hootie 2 solstice's so he should have some gearboxes for you.
Timmbo23, I also gave hootie a KFX so he should have an extra circuit board as well. |
------------------------------------------------
Screamin Demon (600 watt scooter motor, 36v scooter controller)
Red Harley (trike, 24v scooter controller, 13t MFJ gearboxes/motors)
KFX Quad (24v scooter controller, MFJ 12t gearboxes/motors)
Fire Rescue Jeep (24v scooter controller, 15t #7 gearboxes/motors)
Franken(berry)beast (24v scooter controller, 2-250Watt Scooter motors)
Grave Digger (21T gearboxes)
Super Shock
Razor MX-350 Motorcycle
Projects
--------
Jeep Wrangler (on hold)
Barbie Cruzin Tunes Jeep (24v scooter controller)
TCV Indy Racer (24v scooter controller)
Gator (on hold)
Silverado Dragster (on hold)
Apache (on hold)
Metal big wheel (24v scooter controller)
Jeep Aftershock |
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/26/2010 : 18:36:18
|
| What is his e-mail? |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
|
treebeme
Advanced Modder
Holtsville
NY
USA
3209 Posts |
Posted - 10/26/2010 : 19:56:39
|
Here is his profile.
http://www.modifiedpowerwheels.com/forum/pop_profile.asp?mode=display&id=2584 |
------------------------------------------------
Screamin Demon (600 watt scooter motor, 36v scooter controller)
Red Harley (trike, 24v scooter controller, 13t MFJ gearboxes/motors)
KFX Quad (24v scooter controller, MFJ 12t gearboxes/motors)
Fire Rescue Jeep (24v scooter controller, 15t #7 gearboxes/motors)
Franken(berry)beast (24v scooter controller, 2-250Watt Scooter motors)
Grave Digger (21T gearboxes)
Super Shock
Razor MX-350 Motorcycle
Projects
--------
Jeep Wrangler (on hold)
Barbie Cruzin Tunes Jeep (24v scooter controller)
TCV Indy Racer (24v scooter controller)
Gator (on hold)
Silverado Dragster (on hold)
Apache (on hold)
Metal big wheel (24v scooter controller)
Jeep Aftershock |
|
|
|
|
|
TerryInLeesburg
Journeyman Modder
Leesburg
VA
USA
133 Posts |
Posted - 10/27/2010 : 05:56:09
|
quote:
Originally posted by timmbo23
quote:
Originally posted by NSAELLIS
That sucks I guess I'm going to have to brake down and take it to the Power wheels service center in town and have then replace the motor unless some one can tell me how to remove the gear off the motor. IF i can do that I can take one of the many motors I have and swap it. Any one?
I think it is almost impossible to get the gear (pinion) off of the stock motor on the newer Power Wheels. Your best bet is to find a motor with the proper number of teeth on it. Personally I would tell you this is a great time to buy 2 HPI GT550 motors and upgrade your Hurricane so it is much faster. You can find those motors for about $14 each (sometimes even a few bucks less!). You will also need to purchase 2 pinions which are usually $3 or $4 each, quick and easy to do and does not require a PW service center!!!!!
Where can I ge the pinions? I have 2 550 GT's on order, but could not find the piniojns.
Also, where is the best place to get heat sinks?
Thanks a lot
Terry |
Just learning... |
|
|
|
timmbo23
Journeyman Modder
104 Posts |
Posted - 10/27/2010 : 07:39:20
|
| Any R/C hobby store will have them. They are 32 pitch, and get the proper number of teeth. |
PW Ford F150 (2-Seat) - 18v / Dual HPI GT 550 Motors / LED Headlights
PW Kawasaki Ninja KFX - 18v / Dual HPI GT 550 Motors / LED Headlights |
|
|
| |
Topic |
|
Motor Needed
Forum Locked
